高清在线不卡一区二区应用,国产69XXXXX精品免费,白浆高潮在线}

Type Selection Instructions for Horizontally Installed Metal Tube Rotor Flowmeter

File Name：Type Selection Instructions for Horizontally Installed Metal Tube Rotor Flowmeter
Add Time：2019-04-12 10:30:19
Document Size：
Recommendation：
Immediately Download：

Download Instructions：

、產品概述：">Productoverview:
、準確度高

、適用范圍廣

。">ZW-LZR series horizontal metal tube rotameter has the advantages of simple structure, reliable work, high accuracy, wide application range. 。">Compared with glass rotor flowmeter can resist high pressure. 、電遠傳

、限位開關報警、耐腐蝕

、夾套型

、阻尼型和防爆等品種。">LZ series flowmeter has the local indication, limit switch, electric remote alarm, corrosion resistance, damping and explosion-proof type jacket, etc.. ，特殊場合也可由0Cr18Ni12Mo2Ti 或 F46 等耐腐蝕材料組成

。">Some parts are made of 1Cr18Ni9Ti stainless steel meter testing materials, special occasions can also be composed of 0Cr18Ni12Mo2Ti or F46 corrosion resistant materials.。">In addition to the flowmeter special specifications, the height was 250 mm.，也可根據用戶特殊要求定制。">Connecting flange with GB/T9119.8 - 10 standard, also can be customized according to the special requirements of users.
、結構和計量原理：">Second, the structure and principle of measurement:
、結構：">1, structure:
ZW-LZR series horizontal metal tube rotameter is mainly composed of:
，就地指示器）

；">A (Intelligent indicator, indicator, local indicator);
；">B, float;
、錐形測量室。">C, a conical measuring chamber.
、計量原理：">2, the principle of measurement:
，當浮子所受上升力大于浸在流體中浮子重量，浮子便上升

，環隙面積就隨之增大

，環隙處流體流速立即下降，浮子上下端差壓降低

，作用于浮子的上升力亦隨著減少

，直到上升力等于浸在流體中浮子重量時，浮子便穩定在某一高度

。">On the lower end of the measured medium from the measuring tube through a conical float generating differential pressure form the upward force, when the float on the lift is greater than immersion float in the fluid weight, the float will rise, annulus area increases, the annulus fluid velocity decreased immediately, float on the lower pressure reduced, to float up with the decrease in stress, until the lift is equal to the weight of the float when immersed in a fluid, the float will stabilize at a certain height.。">The float position that corresponds to the size of the measured medium flow.，磁場隨浮子的移動而變化

。">A built-in magnet, the float with the medium moves up and down, with the movement of the float magnetic field changes.
，由就地指示器中的旋轉磁鋼與浮子內磁鋼耦合

，而發生轉動，同時帶動指針，通過刻度盤指示出此時的流量大小

。">A, for in situ, by rotary magnetic float and the local indicator in the inner magnetic coupling, rotate, and drives the pointer, through the dial indicates the size of the flow.
、對于智能型，由智能型指示器中的一個固態磁傳感器將磁場的變化轉化成電信號

，經A/D變換

、微處理器，D/A輸出

，LCD液晶顯示

，來顯示出流量的大小及累積流量。">B, the intelligent, by a solid state magnetic sensor intelligent indicator in the magnetic field will change into electrical signal output by A/D transform, D/A microprocessor, LCD liquid crystal display to show the size and cumulative flow flow.
、廣泛應用：">Three, widely used:
，石油、化工

、發電

、制藥、食品

、水處理等

。">The installation of ZW-LZR series horizontal metal tube rotameter is widely used in petroleum, chemical, power, pharmaceutical, food, water treatment, etc.. ，及各種介質條件的流量測量過程中

。">The complex, harsh environmental conditions, the flow measurement process and various medium conditions in.
Fourth, the product structure:
、采用全金屬結構

，有普通型、阻尼型

、高溫型

、高壓型

。">1, with all metal structure, common type, high temperature, high pressure, damping type type type.
、根據客戶管道情況，測量管結構可分為：下進上出

、下進上橫出

、下橫進上橫出、右進左出

、左進右出

。">2, according to the customer the pipe, the measuring tube structure can be divided into: in the cross, lower upper and lower transverse into cross, right into the left, the left into the right.

。">3, this series of metal tube rotameter consists of 2 parts: the measuring tube and indicator.

、導向器、止動器、浮子等部件

，指示器包括磁隨動系統

、指針、刻度盤

、線路等組件

。">The measuring tube comprises a conical tube or plate, guide, stopper, float and other components, including magnetic indicator servo system, a pointer, a dial, lines and other components.
Fifth, main features:

、全金屬結構

，堅固穩定，適合高溫高壓

，強腐蝕性介質

。">1, all metal structure, strong stability, suitable for high temperature and high pressure, strong corrosive medium.

，原裝進口繼電器輸出

，保證動作可靠。">2, using the isolation design, imported relay output, to ensure reliable operation.
、于各行業的氣體和液體測量

，測量部分可采用不同的材質來適應不同的介質條件。">3, in all sectors of the measurement of gas and liquid, the measuring part can be using different materials to adapt to various medium conditions.
、垂直

、水平、各種安裝方式更適合不同使用場合

。">4, the vertical and horizontal installation, more suitable for different occasions.
、磁性耦合結構確保數據傳輸、信號更加穩定

。">5, the magnetic coupling structure to ensure data transmission, more stable signal.
、可加磁過濾器，可帶保溫或夾套設計

。">6, magnetic filter, with thermal insulation or jacket design.

、垂直、水平

、各種安裝方式更適合不同使用場合

。">7, the vertical and horizontal installation, more suitable for different occasions.
、可用于易燃

、易爆危險場合。">8, can be used in flammable and explosive occasions.

、技術參數：">Six, technical parameters:

，2.5-150000L/h

，空氣（20℃

，0.1013MPa）0.07-4000Nm3/h；">Measuring range: water (20 C), 2.5-150000L/h, air (20 DEG C, 0.1013MPa 0.07-4000Nm3/h);

；">Range: 10:1;

；">Measurement accuracy: 1.5/2.5;
Working pressure: 6.4MPa;

；">Working temperature: -40 to 350 DEG C (fluorine plastic lined -10 to 80 DEG C);

；">Ambient temperature: -20 to 80 DEG c;

；">Medium viscosity: DN15 = DN25, DN150 = ~;

；">Tube material: 1Cr18Ni9Ti, 316L, PTEF lining;

；">Installation: flange, or as required;

；">The basic error: 1.5%;
Output signal: 4 ~ 20mA;

；">Load impedance: 350 ohms;

；">Power supply: 24VDC;
Electrical connection: M20 * 1.5;

。">Explosion proof mark: ExibIICT4.

、結構分類說明：">Seven, structure classification:
1, the high temperature structure (G type)

。">High temperature structure type (G type) is used for medium temperature is too high or too low and the need to take measures on the insulation of the measuring tube medium flow measurement.

、增加隔熱材料厚度，保證指示器工作在允許的環境溫度范圍內

。">The high temperature structure is increased and the distance between the measuring tube indicator to increase heat dissipation and increase the insulation thickness, ensure the working environment temperature indicator in the allowable range.

。">The selection of the "G" type.
Flow type G metal tube rotameter can measure the temperature of -80 DEG -+300 DEG medium.
、帶阻尼器裝置的結構（Z型）">The structure of 2, with a damper device (Z type)
，特別是對于氣體的測量。">Damper structure type flowmeter for entrance flow (pressure) medium flow measurement is unstable, especially for gas measurement.
、夾套型結構(T型)">3, jacket type structure (T type)
。">Jacket structure for heating or cooling of needs (such as high viscosity and flow measurement of the medium Yi Jiejing).

。">In the jacket by heating or cooling medium, low boiling fluid and vaporization crystallization.
Import and export with thermal medium connection standard to use HG20594-97 DN15 PN1.6 flange, flange connection and other specifications may be marked with production plant, pressure rating jacket for 1.6MPa.

、外形尺寸圖。">Jacket type flowmeter structure see FA standard flange type flowmeter and the size of map.

、高壓型結構(Y型)">4, high pressure type structure (Y type)
High pressure type structure for media pressure is greater than the standard pressure level measurement.

。">High pressure type structure as shown below.

。">At present, the maximum pressure can reach 32MPa FFM64 series.In addition high pressure type flowmeter can provide built-in magnetic filter type, installation height is 350mm.

、FB和FC型***大壓力為10MPa

。">FA, FB and FC type maximum pressure of 10MPa.
Eighth, the installation should follow the following steps:

、在安裝到工藝管道之前

，應拆卸所有安裝并檢查有沒有運輸損壞；">1, before installation to process piping, should remove all installed and checked for any transport damage;

、為防止在運輸途中,指示器中裝有固定指針的橡皮筋,接線前應打開指示器左蓋把它輕輕取走

，不要指針位置變化；">2, in order to prevent in transit, with a rubber band fixed pointer indicator, indicator should open the left cover it gently removed before connection, do not change the pointer position;

、打開指示器右蓋

，電纜線穿過電纜引入裝置后，按旋轉角變送器的接線圖接線后

，旋緊壓螺母

，使電纜固定，然后旋緊左右蓋的緊固螺釘

，使指示器防水防塵

；">3, open the indicator of the right cover, cable through the cable introducing device, according to the wiring diagram wiring rotation transmitter, pressure screw nut, the cable is fixed, and then tighten the fastening screws around the cover, the indicator of waterproof and dustproof;

，儀表上游直管段長度應保證是儀表公稱口徑的5倍

，下游直管段長度h2不少于250mm；">The upstream and downstream pipeline 4, instrument and instrument should be the same caliber, flange or threaded connection should be matched with the flange and screw instrument, instrument upstream straight pipe length should ensure that the instrument is 5 times the nominal diameter, downstream straight pipe length not less than H2 250mm;
、由于儀表的測量機構采用的是磁傳遞

，所以為了保證浮子流量計的性能，傳感器的安裝周圍至少100mm處

，不允許有鐵磁性物質存在

；">5, the instrument measuring mechanism is magnetic transfer, so in order to ensure the performance of rotameter installed around the sensor, at least 100mm, the existence of ferromagnetic material is not allowed;
，防止管道中滯留的鐵磁性物質附著在儀表里

，影響儀表的性能，甚至?xí)p壞儀表.如果不可避免

，應在儀表的入口安裝磁過濾器

；">Before installation, 6 meter pipeline sweeping shall be carried out, to prevent the retention of ferromagnetic material in the pipeline is attached to the instrument, the instrument performance, or even damage the instrument. If unavoidable, should be installed at the entrance of the magnetic filter instrument;
，將會在浮子處產生壓降,并引起數據失真

。">7, the measurement of gas meter is calibrated in special pressure, if the gas meter in the outlet directly discharged into the atmosphere, will produce a pressure drop in the float, and lead to data distortion.，以便能對所需流量值進行設定

，當浮子上維持標校壓力時

，氣體將在閥門處膨脹；">If this is the working conditions, should install a valve in the instrument exports, so that the required flow value is set, when the float to maintain calibration pressure, gas expansion in valve;
、儀表的安裝形式分為垂直安裝和水平安裝

，如果是垂直安裝形式，應保證儀表的直度優于1%

；如果是水平安裝形式應保證儀表的水平度優于1%

；">The installation form 8, instrument installation for vertical and horizontal installation, if it is installed in a vertical straight form, should ensure that the instrument is better than 1%; if the level of installation form should ensure that the level of less than 1% meters;
，儀表的出口和入口應有合適的管道支撐,可以使儀表處于***小應力狀態

；">9, installed in the pipeline in the instrument should not be subject to stresses, the instrument should be a proper entrance and exit pipe support, can make the instrument in the minimum stress state;

，須***在安全場所進行

。">10, products and computer related to calibration and other operations, must be in a safe place.
The installation notes:

、儀表到達現場

，在安裝到工藝管線之前，應開箱拆卸所有包裝并仔細檢查儀表是否有運輸損壞

。">1 instrument, arrived at the scene, before installing the pipeline to remove all packing and unpacking, should carefully check whether the instrument for transport damage.
、儀表在安裝前，對工藝管線應進行吹掃清理

，防止管道中留有鐵磁性雜質附屬在儀表的浮子上

，影響儀表的正常測量，嚴重的會造成儀表的損壞

。">2, the instrument before installation, the pipeline should be blowing clean, prevent pipeline have ferromagnetic impurities attached to the instrument on a float, affect the normal measuring instruments, will cause serious damage to the instrument.，應在儀表的入口安裝磁過濾器。">If cannot avoid, should be installed in the entrance of the magnetic filter instrument.
、由于儀表的測量機構采用磁傳遞和磁電信號處理器

，為保證儀表的正常使用和性能，安裝范圍至少500mm 內不允許有鐵磁性物質

、強磁場和較強的電磁場存在

。">3, because of the measuring mechanism of instrument by using magnetic transmission and magnetic signal processor for normal use and performance guarantee instrument, installation of a range of at least 500mm are not allowed in the presence of ferromagnetic materials, strong magnetic field and strong electromagnetic field.
，不應受到應力的作用

，儀表的出入口，應有合理的管道支撐

，使儀表在工藝管道上受到***小的應力

。">4, installed in the pipeline in the instrument, should not be subject to stresses, instrument entrances should be reasonable to support, so that the instrument is the minimum stress in the process pipeline.
，垂直安裝的儀表

，應保證儀表的垂直度

，傾斜偏差不大于3 度

；水平安裝的儀表

，應保證儀表的水平直度，傾斜偏差不大于3 度

。">5, instrument installation is divided into horizontal and vertical installation installation, vertical installation of the instrument, instrument should ensure the verticality, tilt deviation is not greater than 3 degrees; the level of instrument installation, should guarantee the instrument level straightness, angle deviation is not greater than 3 degrees.
、儀表在安裝時，上下游管道的口徑應與儀表的口徑相同

，連接法蘭應相互匹配

；為保證儀表的測量精度和穩定性，儀表上游直管段長度為儀表公稱口徑的5 倍

，下游直管段***小長度為250mm

。">6, the instrument at the time of installation, the upstream and downstream pipeline diameter and the instrument should be the same caliber, the flange should be matched with each other; in order to ensure the accuracy and stability of the instrument, the instrument upstream straight pipe length is 5 times the nominal diameter of the instrument, the minimum length of 250mm downstream straight pipe.
，如果儀表直接向大氣中排放氣體

，會造成儀表的數據失真甚至儀表的損壞。">7, the measurement of gas meter, gas meter if discharge directly to the atmosphere, even damage the instrument will cause distortion meter data. ，應在儀表的出口處安裝節流閥

。">In this condition, the throttle valve should be installed at the exit of the instrument.
，要特別小心

，在低溫條件下，P T F E 在壓力的作用下也會變形

，所以安裝時不要隨意擰緊

。">8, install the P T F E lining instrument, to be especially careful, at low temperatures, P T F E will deform under the action of pressure, so do not tighten the installation.
，要盡量避免陽光直射顯示器

，以免降低液晶使用壽命；帶有鋰電池供電的儀表

，要盡量避免陽光直射

、高溫環境（≥65℃）以免降低鋰電池的容量和壽命。">9, with a liquid crystal display instrument, to avoid direct sunlight, so as not to reduce the service life of the liquid crystal; with lithium battery powered instruments, to avoid direct sunlight, high temperature (65 DEG C) to reduce the capacity and lifetime of lithium battery.
、產品維護：">Ten, product maintenance:
、在長期的使用過程當中，管道內不可避免會有鐵磁性雜質吸附在浮子上

，這樣會將浮子卡死或影響測量精度

，要時常對傳感器內浮子進行清洗；如果安裝磁過濾器

，也要進行定期清洗

。">1, in the process of long-term use, the pipeline inevitably there will be ferromagnetic impurity adsorption on the float, it will float stuck or affect the measurement accuracy, from time to time to clean the sensor float; if the installation of magnetic filters should be cleaned regularly.
、儀表指示器內裝有電子元件，儀表接線或拆卸殼體后

，要將螺釘旋緊

，須***保證殼體的密封性，防止雜質

、水或其它物質進入

，同時還要保證儀表殼體的可靠接地。">2, the instrument indicator with electronic components, instrument wiring or demolition of housing, to housing screws, must ensure sealing, prevent impurities, or other material into the water, and also to ensure reliable earthing of the meter casing.
、儀表安裝后

，*********次使用時，要注意：">3, instrument installation, on first use, should pay attention to:

，造成儀表的損壞

，一定要緩慢地打開閥門！">When the valve is opened to avoid the formation of pressure shock makes the float slamming limiting device, causing damage to the instrument, slowly open the valve!

，以***大程度的減小浮子的震蕩

；為確保浮子的穩定性，可以在儀表的出口安裝一節流閥

。">The measurement of gas meter is equipped with gas damper, to minimize the shock; to ensure the stability of the float, a throttle valve can be installed in the instrument export.
、對于遠傳型儀表，首先要保證儀表的接線正確后

，方可通電

；對于危險場合，須***選擇防爆型

，并按防爆要求進行安裝使用

。">4, for the remote type instrument, we must first ensure that the instrument wiring correctly, keeps power; for dangerous situations, must choose the explosion-proof, and the installation and use of proof required by the.

Table eleven, technical parameters:

Path (mm)	Flow range			The pressure loss of KPa
	Water L/h		Air m3/h	water		atmosphere
	The conventional type	Anti-corrosion type	The conventional type / anti-corrosion type	The conventional type	Anti-corrosion type	atmosphere
Fifteen	2.5-25 4.0-40 6.3-63 10-100 16-160 25-250 40-400 63-630	2.5-25 4.0-40 6.3-63 10-100 16-160 25-250 40-400	0.07-0.7 0.11-1.1 0.18-1.8 0.28-2.8 0.48-4.8 0.7-7.0 1.0-10.0 1.6-16.0	Six point five Six point five Six point six Six point six Six point eight Seven Eight point six Eleven point one	Five point five Five point five Five point six Five point six Five point eight Six point one Seven point three	Seven point one Seven point two Seven point three Seven point five Eight Ten point eight Ten Fourteen
Twenty-five	100-1000 160-1600 250-2500 400-4000	63-630 100-1000 160-1600 250-2500	3-30 4.5-45 7-70 11-110	Seven Eight Ten point eight Fifteen point eight	Five point nine Six Six point eight Nine point two	Seven point seven Eight point eight Twelve Nineteen
Fifty	630-6300 1000-10000 1600-16000	400-4000 630-6300 000-10000	18-180 25-250 40-400	Eight point one Eleven Seventeen	Six point eight Nine point four Fourteen point five	Eight point six Ten point four Fifteen point five
Eighty	2500-25000 4000-40000	1600-16000 2500-25000	60-600 80-800	Eight point one Nine point five	Six point nine Eight	Twelve point nine Eighteen point five
One hundred	6300-63000	4000-40000	100-1000	Fifteen	Eight point five	Nineteen point two
One hundred and fifty	20000-100000		600-3000	Nineteen point two		Twenty point three

、選型表：">Twelve, selection table:

Specification code				Explain
The name of the factory	ZW			Zhongwei control
Instrument types		LZ		Metal tube rotameter
structural style		A		In the next
		B		Progress under the
		C		Side measure
		D		The bottom side
		R		Right into the left out
		L		The left into the right
		K		Clamp connection (sanitary polishing tube)
		W		Threaded connection
Size code		- XXX		DN15 said: 15 cases
The measuring tube material		R1		，304">1Cr18Ni9Ti, 304
		R0		0cr18Ni12M02Ti, 316
		RL		316L
		RP		PTFE (PTFE)
		Ni		Hastelloy (Hastelloy C)
		Ti		TitHXium (Tai Hejin)
Media type		L		liquid
		G		Gas
working temperature		H1		- 40 -100 OC
		H2		- 80 -250 OC
Rated pressure		One point six		1.6MPa
		Four		4.0MPa
		Sixteen		16MPa
		Twenty-five		25MPa
Additional structure		O		nothing
		Z		Damping type
		T		Jacket
		H		High temperature type
		Y		High pressure type
Form indicator			M1	Local indication
			M2	Intelligent
			M3	Intelligent (explosion)
The output signal in the communication			N	nothing
			A	4-20mA
			H	4-20mA+Hart
Alarm controller			K1	The upper limit alarm
			K2	Alarm
			K12	、下限報警">The upper and lower limit alarm
Explosion proof type			E1	Intrinsically safe EXiaCT5 square casing
			E2	Flameproof shell EXiibt4 Park
Power supply			Zero	24VDC (optional)
			Two	220VAC
			Three	The 3.6 volt lithium battery

Browse：

On A：Type Selection Instructions for Threaded Metal Tube Rotor Flowmeter

Next：Type Selection Instructions for Micro Flow Metal Tube Rotor Flowmeter

分享到：

公交车上拨开少妇内裤进入电影,同桌把我下面摸高潮视频,尤物视频在线国产,国产一区二区三区深田咏美,久久婷婷丁香五月综合开心,亚洲高清情侣网站,国产欧美日韩手机在线不卡,丝袜美女污污免费网站,一本色综合久久,seerx性欧美老妇,少妇挑战三个黑人惨叫4p国语,91白浆视频在线,影音先锋蜜芽视频,囯产偷拍一区二区三区,水多多凹凸福利视频导航,国产免费A∨在线播放,无遮挡又爽又刺激的免费观看