Product

Flow meter series

Pressure Instrument Series

Thermometer Series

Display Instrument Series

Recording instrument series

Calibration instrument series

Proxy instrument series

Control valve series

Universal valve series

Valve fittings series

Cable tray series

Level instruments

0517-86918678

Address：No. 4-4 East West Road, Jinhu County Industrial Concentration Zone, Huaian City, Jiangsu Province
Tel：0517-86918678
Fax：0517-86918679
Email：zhongweick@163.com
Post Encoding：211600

Home /Product /Flow meter series /Lumbar Wheel (Roots) Flowmeter

Lumbar Wheel (Roots) FlowmeterLumbarWheelRootsFlowmeter

Cast steel turbine flowmeter

ZW-LL series Cast steel turbine flowmeter Mainly used for large diameter gas flow measurement, all k…

Description：

、產品概述：">

、產品概述：">Productoverview:

ZW-LL series Cast steel turbine flowmeter 、液體

、蒸汽介質流體的流量測量

。">Mainly used for large diameter gas flow measurement, all kinds of industrial liquid in the pipe and steam medium fluid. 、壓力

、溫度、粘度等參數的影響

，無可動機械零件

，因此可靠性高,維護量小。">It is characteristic of small pressure loss, large measuring range, high accuracy, influence of the measuring condition of volume flow rate is almost not affected by fluid density, pressure, temperature, viscosity and other parameters, so no moving mechanical parts, high reliability, small amount of maintenance. 。">The instrument parameters can work stably for a long time.

，計量室內有一對或兩對可以相切旋轉的腰輪。">The utility model is characterized in that a metering chamber in the meter casing, the metering chamber has a pair or two pairs of tangent waist wheel rotation. ，它們相互嚙合使兩個腰輪可以相互聯動

。">In the outside of the casing and two meter coaxial search round a set of transmission gears meshing with each other, they make the two round the waist can be linked with each other.

。">ZW-LL series steel flowmeter in the structure, the outer legs and waist wheel flowmeter the inner wall of the shell surface can be composed of a certain volume of the "bucket" space. We called the measuring room". ，在流量計進出口流體差壓的作用下.兩腰輪將按正方向旋轉。">When the fluid flow through the flow meter in timing, the import and export of differential fluid pressure under the action of two. According to the positive direction of rotation of the waist wheel. 。">The formation of a metering chamber enclosed by the waist wheel and the shell. 。">The fluid metering chamber filled with a single volume of imports from the waist wheel is divided into continuous fluid.

Two, work principle:

，在流量計的進出口形成壓差

，腰輪在此壓差的推動下旋轉。">ZW-LL series steel flowmeter is measured when the fluid flows through the metering chamber, in the import and export of the formation of differential pressure flowmeter, this pressure waist wheel driven by rotation. ，使兩個腰輪保持連續旋轉

。">At the same time through fixed at the waist on the axle of the driving gear, the two round of continuous rotation of the waist. 。">With the rotation of the waist wheel, the metering chamber is discharged continuously through the liquid flowmeter. ，通過密封聯軸器、減速機構

，將旋轉次數減速后傳遞到計數器，計數器即指示液體瞬時流量和累積流量

。">The amount of each liquid flow through the metering chamber volume is four times, the sealing mechanism through the coupling, reducer, reducer rotating number is transferred to the counter, the counter is indicating liquid instantaneous flow and cumulative flow. 。">Install the transmitter in the counter mechanism that the sender of the waist belt. 、累積

、瞬時等功能）自動化測量和控制。">With the display meter or computer system can realize remote (quantitative, cumulative and instantaneous automatic measurement and control function). 。">Use display instrument Classification Manual see.

、應用計量：">Three, application of measurement:

，重油等高粘度液體的流量計量

；">ZW-LL, can be used for pure crude oil, heavy oil flow measurement of high viscosity liquid;

、重油等高粘度流體的流量計量；">ZW-LL-D can be used to prevent sand sand flow measurement of crude oil, heavy oil and other high viscosity fluid;

，具有較強的防腐性能

，可用于腐蝕性液體的流量計量，特別適用于化工行業

；">Contact type flowmeter and ZW-LL-F stainless steel medium stainless steel material manufacturing, has strong corrosion resistance, can be used for flow measurement of corrosive liquid, especially for the chemical industry;

，柴油等低粘度流體的流量計量。">ZW-LY-C light oil type is especially suitable for light oil, diesel oil flow measurement of low viscosity fluid.

、主要特點：">Four, main features:

、測量準確度高，基本誤差一般可達正負0.2%到正負0.5%

，特殊要求時可達正負0.1%,流量計的特性一般不受流動狀態的影響

，也不受雷諾數大小的限制。">1, high measurement accuracy, the basic error is generally up to plus or minus 0.2% to plus or minus 0.5%, special requirements up to plus or minus 0.1%, flow characteristics generally not affected by the flow state, nor by the Reynolds number size limit.

、可用于高粘度液體的流量測量">2, can be used for high viscosity liquid flow measurement

、測量范圍度較寬，典型的流量范圍度為5：1到10：1">3, a wide range of measurement, the typical flow range of 5:1 to 10:1

、字輪式計數器累積流體總量

，無需外部能源，使用方便面計數器累積流量雙顯示

，其中之一可以復零

，方便用戶在不連續計量的情況下使用。">4, the cumulative amount of fluid type wheel counter, without external energy, the use of instant noodles counter cumulative flow double display, one of which can be reset to zero, the convenience of users in the case of continuous measurement.

、計量部件之間無接觸

，不磨損，使用壽命長

。">5, the measurement between components without contact, no wear, long service life.

、大口徑流量計采用又轉子形式，降低流量計運轉噪聲和振動

。">6, large caliber flowmeter and the rotor, reduce running noise and vibration meter.

、技術參數：">Five, technical parameters:

、±0.2%

、±0.5%；">1, allow the basic error: + 0.1%, + 0.2%, + 0.5%;

、公稱通徑DN（mm）：15～300

；">2, the nominal diameter of DN (mm): 15~300;

、不銹鋼（P） 1 .0

、1.6

、2.5、4.0

、6.3

；鑄鋼（E）2.5、4.0

、 6.3

、9.6；">3, nominal pressure PN (M.Pa): cast iron, stainless steel (A) (P) 1, 1.6, 2.5, 4, 6.3; 2.5, 4 cast steel (E), 6.3, 9.6;

、被測液體溫度：">4, the measured liquid temperature:

；">A. low temperature: -40 ~ +60 c;

B. at room temperature -10 to +80 DEG c;

；">The temperature of C. -10 to +200 DEG c;

；">D. high temperature -10 to +300 DEG c;

；">5, the measured liquid viscosity (mPa.s): 0.3 ~ 50000;

、管道連接：GB/T9118-2000（zg****標準法蘭）；NIST（美國標準法蘭）

；BSPT（英國標準管螺紋）：NPT（美國推拔管螺紋）

；">6, pipe connection: GB/T9118-2000 (Chinese; NIST (American Standard) standard); BSPT (BSP): NPT (American pipe thread);

；9999,999.9 L（瞬時流量）

；">7, on-site display: 99999999 L (cumulative flow) of 9999999.9 L (single flow); 9999999.9 L (transient flow);

、4～20mA

、1-5V、4～20mA +HART協議

、MODBUS支持RS232

、RS485通訊（任選）；">8, output signals: pulse signal, 4 ~ 20mA, 4 ~ 1-5V, 20mA +HART, MODBUS RS232, RS485 protocol support communication (Ren Xuan);

、防爆等級：EXiaIIBT5EXiaIICT5防護等級：IP65

。">9, explosion-proof grade: EXiaIIBT5EXiaIICT5 protection grade: IP65.

Six, installation and use:

、流量計前應安裝過濾器，兩者表體上箭頭指向與流動方向一致

。">1, flow meter should be installed before the filter, the meter with the direction of arrow.

、當被測液體含有氣體時，流量計前應安裝氣體分離器

。">2, when the measured liquid containing gas, flow meter should be installed before the gas separator.

、不論管路是垂直還是水平安裝

，但流量計的腰輪軸安裝成水平位置（即表度盤應與地面垂直）。">3, whether the pipeline is vertical or horizontal installation, but the waist wheel flowmeter installation into a horizontal position (i.e. dial should be perpendicular to the ground).

、流量計在正確安裝情況下

，如果不易看清讀數，可把計數器旋轉180度或90度均可

。">4, the correct installation of flowmeter in the case, if it is not easy to see the readings, the counter rotating 180 degrees or 90 degrees can be.

、節流閥應安裝在流量計進口處，開閉閥裝在出口處

，使用開閉閥時要緩慢啟動

，不要突然開閥。">5, the throttle valve should be installed in the meter inlet opening and closing valve is installed at the outlet, the use of open or close the valve to start slowly, do not suddenly open valve.

、嚴禁使用掃線蒸汽通過流量計

。">6, prohibited the use of steam flowmeter by line sweep.

，流量計需加旁通管道

。">7, in the continuous use of departments, need to add a bypass pipeline flowmeter.

，管道需沖洗

，沖洗時采用直管段（替代流量計位置）防止焊渣、雜物等進入流量計

。">Before the installation of 8, flow meter, pipeline flushing, flushing the pipe (alternative meter position) prevent the welding slag and other debris into the meter.

、嚴禁用水校驗鑄鐵、鑄鋼材質組成的流量計

。">9, check the water meter is composed of cast iron, cast steel.

、流量計在使用時流量大小不得超過技術要求。">10, when using the size of the flow meter shall not exceed the technical requirements. 。">The flowmeter work on Zui flow 70~80% was better.

、被測液體如果具有化學腐蝕性，需選用不銹鋼材質的流量計

，如果腐蝕性強

，需選用0Crl8Ni12MO2Ti材質的流量計。">11, if the measured liquid is corrosive, need to use stainless steel flowmeter, if corrosive, need to use 0Crl8Ni12MO2Ti material flow meter.

、安裝注意事項：">Seven, installation notes:

、在安裝前不得隨意打開流量計的進氣，出氣兩封口

；">1, before installation shall not open the inlet flow, the outlet seal two;

、當管道上安裝的設備較多時，流量計應放在后安裝

；">2, when the pipe is installed on the device more, should be put on after the installation of flow meter;

、在條件允許的情況下

，安裝前須***對管道進行高壓吹掃；">3, where conditions permit, the pipeline must be high pressure purge before installation;

、安裝時應對接口處的鐵銷

，毛刺進行細心清除；">4, the installation should at the interface of iron pins, careful removal of burr;

、流量計的前面須***安裝過濾網

，對測量介質進行過濾;測量液體時，若其中含有氣體

，流量計前選裝消氣裝置

，確保流量計的測量精度；">In front of the 5 meter must be installed, filter, filter media measurement; measurement of liquid, if containing gas, optional getter device flowmeter, ensure the measuring precision of flowmeter;

、安裝方式多樣

，水平豎直安裝均可，豎直安裝上進下出

，下進上出不受影響

，但流量計不得反裝，反裝時

，流向相反

，腰輪反轉，因間正反轉隙設計不同會損壞腰輪

；">6, installation modes, horizontal vertical installation can be installed vertically progress under the lower upper is not affected, but the meter shall not be reversed, anti loaded, opposite directions, waist wheel reversal, because the rotation between different gap design will damage the waist wheel;

、對直管段要求較低，但須預留足夠的安裝過濾裝置的距離

；">7, on the lower straight pipe section, but must set aside to install filtering device enough distance;

、腰輪轉動是靠流體的壓差為動力的，當測量介質的粘稠度過大時

，影響流量計測量精度

；">8, the waist wheel rotation by fluid pressure is the force of viscous medium, when the measurement is too high, affect the measuring precision of flowmeter;

。">To avoid the above points, the measurement precision can achieve better flowmeter.

、技術性能：">Eight, technical performance:

project Model	Nominal diameter (mm)	Nominal pressure (Mpa)	The measured liquid temperature (c)	Flow range (M? /h)		% accuracy		The installation form
project Model	Nominal diameter (mm)	Nominal pressure (Mpa)	The measured liquid temperature (c)	Z small flow	Z flow	% accuracy		The installation form
ZW-LL-8	Eight	0~1.6 0~2.5 0~4.0 0~6.4		Zero point two five	Two point five	Zero point two	Zero point five	Horizontal and vertical
ZW-LL-15	Fifteen			Zero point two five	Two point five	Zero point two	Zero point five	、立式">Horizontal and vertical
ZW-LY-20	Twenty		-20~+60	Zero point two five	Two point five	Zero point two	Zero point five	、立式">Horizontal and vertical
ZW-LL-25	Twenty-five			Zero point six	Six	Zero point two	Zero point five	Horizontal and vertical
ZW-LL-40	Forty			One point six	Sixteen	Zero point two	Zero point five	、立式">Horizontal and vertical
ZW-LL-50	Fifty		-20~+120	Two point five	Twenty-five	Zero point two	Zero point five	、立式">Horizontal and vertical
ZW-LL-80	Eighty			Six	Sixty	Zero point two	Zero point five	Horizontal and vertical
ZW-LL-100	One hundred			Ten	One hundred	Zero point two	Zero point five	Horizontal and vertical
ZW-LL-150	One hundred and fifty		-20~+350	Twenty-five	Two hundred and fifty	Zero point two	Zero point five	、立式">Horizontal and vertical
ZW-LL-200	Two hundred			Forty	Four hundred	Zero point two	Zero point five	Horizontal and vertical
ZW-LL-250	Two hundred and fifty		A heat sink	Sixty	Six hundred	Zero point two	Zero point five	、立式">Horizontal and vertical
ZW-LL-300	Three hundred			One hundred	One thousand	Zero point two	Zero point five	、立式">Horizontal and vertical
Pressure loss: the measured liquid viscosity is less than 30mpa.s, the pressure loss is less than 0.05Mpa.

Browse：

On A：Stainless steel flowmeter

Next：Iron waist wheel flowmeter

分享到：

公交车上拨开少妇内裤进入电影,同桌把我下面摸高潮视频,尤物视频在线国产,国产一区二区三区深田咏美,久久婷婷丁香五月综合开心,亚洲高清情侣网站,国产欧美日韩手机在线不卡,丝袜美女污污免费网站,一本色综合久久,seerx性欧美老妇,少妇挑战三个黑人惨叫4p国语,91白浆视频在线,影音先锋蜜芽视频,囯产偷拍一区二区三区,水多多凹凸福利视频导航,国产免费A∨在线播放,无遮挡又爽又刺激的免费观看